江可達的數位歷程檔

基本資料

姓名:	江可達
系所:	修平科技大學 / 機械工程系 [數位教學紀錄]
辦公(研究)室:	B302-2

自我介紹

1. 喜歡孤獨旅行於不知名的小鎮

2. 喜歡多看多聽於旅行中

3. 單車走天崖是我的夢想

4. 水煎包是我最愛的美食

學校經歷

1. 國立中興大學 / 應用數學所博士 (博士, 1992-09 ~ 1993-02)

工作經歷

1. 修平科技大學機械工程系 / 教授 (2008-10 ~ )
2. 修平科技大學 / 教師 (1989-08 ~ )

個人著作

期刊論文

1.	江可達, "Modeling and analyzing the effects of air-cooled turning on the machinability of Ti–6Al–4V titanium alloy using the cold air gun coolant system [International Journal of Advanced Manufacturing Technology]," , 2013.
2.	江可達, "Modeling and analyzing the effects of air-cooled turning on the machinability of Ti–6Al–4V titanium alloy using the cold air gun coolant system [The International Journal of Advanced Manufacturing Technology]," , 2013.
3.	江可達, "Experimental investigation of tool vibration and surface roughness in the precision end-milling process using the singular spectrum analysis [The International Journal of Advanced Manufacturing Technology]," , 2012.
4.	江可達, "Experimental investigation of tool vibration and surface roughness in the precision end-milling process using the singular spectrum analysis [International Journal of Advanced Manufacturing Technology ]," , 2012.
5.	江可達, "Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology [International Journal of Advanced Manufacturing Technology]," , 2012.
6.	江可達, "Investigating the machinability evaluation of Hadf [Journal of Materials Processing Technology]," , 2011.
7.	江可達, "Modeling and analysis of the edge disintegration in the EDM drilling cobalt-bonded tungsten carbide, The International Journal of Advanced Manufacturing Technology [The International Journal of Advanced Manufacturing," , 2010.
8.	江可達, "Analytic transient solutions of a cylindrical heat equation with a heat source [Applied Mathematics and Computation]," , 2009.
9.	江可達, "Modeling and analysis of the effects of processing parameters on the performance characteristics in the high pressure die casting process of Al–SI alloys [The International Journal of Advanced Manufacturing Technolog," , 2009.
10.	江可達, "Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide [The International Journal of Advanced Manufacturing Technology]," , 2009.
11.	江可達, "Application of response surface methodology in describing the thermal performances of a pin-fin heat sink [International Journal of Thermal Sciences]," , 2009.
12.	江可達, "Designing parameter optimization of a Parallel-Plain Fin heat sink using the grey-based fuzzy algorithm with the orthogonal arrays [nternational Journal of Thermal Sciences]," , 2009.
13.	江可達, "The effect of heterogeneous second phase on the ma [Materials and Design]," , 2008.
14.	江可達, "A grey and fuzzy algorithms integrated approach to [Journal of Materials Processing Technology]," , 2008.
15.	江可達, "Modeling and optimization of designing parameters for a parallel-plain fin heat sink with confined impinging jet using the response surface methodology [Applied Thermal Engineering]," , 2007.
16.	江可達, "Optimization of the WEDM process of particle-reinforced material with multiple performance characteristics using grey relational analysis [Journal of Material Processing Technology]," , 2006.
17.	江可達, "Application of grey-fuzzy logic on the optimal process design of an injection-molded part with a thin shell feature [International Communications in Heat and Mass Transfer]," , 2006.
18.	江可達, "Optimum design parameters of Pin-Fin heat sink using the grey-fuzzy logic based on the orthogonal arrays [International Communications in Heat and Mass Transfer]," , 2006.
19.	江可達, "Application of response surface methodology in the parametric optimization of a pin-fin type heat sink [International Communications in Heat and Mass Transfer]," , 2006.
20.	江可達, "Optimization of the design parameters of Parallel-Plain Fin heat sink module cooling phenomenon based on the Taguchi method [International Communications in Heat and Mass Transfer]," , 2005.
21.	江可達, "Effect of a non-uniform basic temperature gradient Benard-Marangoni convection Stationary and oscillatory analyses [International Communications in Heat and Mass Transfer]," , 2005.
22.	江可達, "應用田口法於CD-ROM碟片托盤射出成型之製程最佳化開發 [修平學報第五期]," , 2002.
23.	江可達, "應用田口法於飲水機承水盤塑膠射出成型過程 [修平學報第五期]," , 2002.
24.	江可達, "銅底效應對電腦散熱片模組散熱能力之影響 [修平學報第四期]," , 2002.
25.	江可達, "The optimal process conditions of an injection-molded thermoplastic part with a thin shell feature using grey-fuzzy logic: A case study on machining the PC/ABS cell phone shell [Materials & Design]," , 0006.
26.	江可達, "Modeling and analysis of the effects of machining [International Journal of Advanced Manufacturing Te]," , 0005.
27.	江可達, "Modeling and analysis of machinability evaluation [Materials and Manufacturing Processes]," , 0005.
28.	江可達, "Effect of silicon particles on the rapidly resolid [International Journal of Advanced Manufacturing Te]," , 0003.
29.	江可達, "Modeling and analysis of the rapidly resolidified layer of SG cast iron in the EDM process through the response surface methodology [Journal of Materials Processing Technology]," , 0002.

國內會議論文

1.	江可達, "纖維複合材料製程中丙酮廢液回收之改善與研究 [中國機械工程學會第三十七屆全國學術研討會]," , 2020.
2.	江可達, "WF30鎢鋼沖頭的光學投影研磨之實驗分析與最佳化 [中國機械工程學會第三十五屆全國學術研討會]," , 2018.
3.	江可達, "端銑削加工於SCM440鉻鉬鋼的飛輪之實驗分析與研究 [中國機械工程學會第三十四屆全國學術研討會論文集]," , 2017.
4.	江可達, "端銑削加工於SCM440鉻鉬鋼的飛輪之實驗分析與研究 [中國機械工程學會第三十四屆全國學術研討會]," , 2017.
5.	江可達, "使用CBN刀具於高速鋼的尾座頂針之車削過程中加工參數最佳化研究 [中國機械工程學會第三十四屆全國學術研討會論文集]," , 2017.
6.	江可達, "使用CBN刀具於高速鋼的尾座頂針之車削過程中加工參數最佳化研究 [中國機械工程學會第三十四屆全國學術研討會]," , 2017.
7.	江可達, "Inconel 718鎳基合金的螺栓研磨過程中加工參數之分析與最佳化 [中國機械工程學會第三十四屆全國學術研討會論文集]," , 2017.
8.	江可達, "Inconel 718鎳基合金的螺栓研磨過程中加工參數之分析與最佳化 [中國機械工程學會第三十四屆全國學術研討會]," , 2017.
9.	江可達, "使用灰色動態模組與滾動模組於熱傳特性的建模: 液態金屬流體於擾流中的熱傳特性研究 [中華民國力學學會第三十八屆全國力學會議]," , 2015.
10.	江可達, "使用灰色動態模組與滾動模組於熱傳特性的建模: 液態金屬流體於擾流中的熱傳特性研究 [2014中華民國力學學會年會暨第38屆全國力學會議]," , 2014.
11.	江可達, "實驗探討使用冷空氣氣鎗冷卻系統的冷卻效應於高速銑削過程 [中國機械工程學會第三十屆全國學術研討會]," , 2013.
12.	江可達, "運用空氣冷卻系統於車削鈦合金過程中刀具溫度與表面粗糙度之驗證與建模分析 [中國機械工程學會第二十九屆全國學術研討會]," , 2012.
13.	江可達, "使用反應曲面法與連續近似最佳法來探討Ti-6Al-4V 鈦合金之線切割放電加工性能與最佳化 [中國機械工程學會第二十九屆全國學術研討會]," , 2012.
14.	江可達, "Optimization and modeling of bottoming-die designing parameters in V-die bending process using the response surface methodology [中國機械工程學會第二十六屆全國學術研討會]," , 2009.
15.	江可達, "電子構裝設備之熱流場數值模擬與散熱分析 [第二十六屆全國力學學術研討會]," , 2002.

書籍及技術報告

1.	江可達, "電腦輔助立體製圖丙級術科實作精解,[翰蘆圖書出版有限公司]," , 2018.

計畫

1. 智能化工具機精密製造與設計整合服務模組課程 (2016-07 ~ 2017-08)
2. 105學年度科學工業園區人才培育輔助計畫智能化工具機精密製造與設計整合服務模組課程 (2016-07 ~ 2017-08)
3. 專業木工圓鋸機生產與開發最佳化輔導 (2014-05 ~ 2014-10)
4. 精密加工產品之開發設計專家系統關懷輔導計畫 (2009-04 ~ 2009-09)
5. 應用節能理念改善與開發最佳化設計技術關懷輔導計畫 (2009-04 ~ 2009-09)
6. 風扇葉片3D圖檔設計輔導計畫 (2008-08 ~ 2008-12)
7. 呼吸管快速樣品開發計畫 (2007-09 ~ 2007-12)
8. 工具把手快速樣品開發 (2007-01 ~ 2007-07)
9. 管路壓鑄件快速樣品開發 (2006-12 ~ 2007-01)
10. 修平技術學院進修部招生行銷策略規劃之研究 (2005-01 ~ 2005-10)
11. 快速樣品/模具開發整合流程技術開發案 (2004-03 ~ 2005-02)
12. CAD-3D實體模型建構系統Solidworks套裝軟體教育版 (2003-09 ~ 2004-08)
13. 散熱機構設計與開發最佳化輔導
14. 專業花崗石量儀生產與開發最佳化輔導

獲獎榮譽

1. 至善獎 (2020-09)
2. 弘道獎 (2020-09)
3. 勞動署_銑床-CNC銑床_乙級證照[182-003231] (2015-02)
4. 教學優良教師 (2011-12)
5. 交通部_民營汽車駕駛人、訓練[交路機構字第中培1001號] (2009-02)
6. 家弘學術研究優良人員-著作論文 (2008-12)
7. 行政院勞工委員會_汽車修護_乙級證照[020-038242] (2008-02)
8. 交通部_汽車修護技工執照[6.50E+16] (2008-02)
9. 教學優良教師 (2007-12)
10. 家弘學術研究優良人員 (2007-12)
11. 交通部_汽車修護技工職照[6.50E+16] (2007-02)
12. 大智獎 (2005-09)
13. 行政院勞工委員會_電腦軟體應用_乙級證照[118-008198] (2003-02)